生物质颗粒机生产厂家分享环模配件使用完毕如何处理

来源:http://www.longtengkeliji.com 发布时间:2019-11-12 浏览次数:
  颗粒机关闭时,应使用无腐蚀性的将原来的油环的模具部分饲料挤压,否则,环模部分的热量将留在模具孔饲料的原料干燥困难,导致如下:(2)开始生产,环模配件承担高压力,削弱它的力量,这可能会导致环模配件开裂;(3)部分模具孔堵塞,产量和效益下降。2、环模配件使用一段时间后,应检查环模配件表是否有局部凸出的部分,如有此现象,应将环模配件进行修理,以确保……
  When the particle mechanism is closed, the feed of the original oil ring die should be extruded by non corrosive way, otherwise, the heat of the ring die part will remain in the feed of the die hole, which is difficult to dry, resulting in the following: (2) starting production, the ring die parts bear high pressure and weaken its force, which may lead to cracking of the ring die parts; (3) part of the die hole is blocked, and the output and benefit decrease. 2. After using the ring mold accessories for a period of time, check whether there is any part protruding in the ring mold accessories list. If there is such a phenomenon, repair the ring mold accessories to ensure that
  当颗粒机停机时,在环模配件内的进料应挤出无腐蚀性的油,否则,在环模配件内的热量会使原料在饲料的模孔内干燥变硬,造成以下情况:
生物质颗粒机生产厂家
  When the granulator is shut down, the feed in the ring die fitting shall be extruded with non corrosive oil, otherwise, the heat in the ring die fitting will make the raw material dry and hard in the die hole of the feed, resulting in the following conditions:
  ()操作开始时,模具孔堵塞,物料无法挤出;
  () at the beginning of operation, the die hole is blocked and the material cannot be extruded;
  (2)生产初期,环模配件受力大,强度变弱,容易造成环模配件开裂;
  (2) at the initial stage of production, the ring mold parts are subject to large stress and weak strength, which is easy to cause cracking of the ring mold parts;
  (3)部分模具孔堵塞,产量和效益下降。
  (3) some die holes are blocked, the output and benefit decrease.
  合金钢环模
  Alloy steel ring die
  2、环模配件在一段时间后,应检查环模配件表是否有局部凸的部分,如果有这样一个现象,环模配件应该维护,以确保环的输出模具配件和辊的使用寿命。
  2. After a period of time, the ring die parts list shall be checked to see if there is any local convex part. If there is such a phenomenon, the ring die parts shall be maintained to ensure the service life of the ring output die parts and rollers.
  3、环模配件储存在干燥、清洁的地方,如果储存在潮湿的地方,会产生模孔腐蚀,降低环模配件或无材料的使用寿命。
  3. The ring mold accessories shall be stored in a dry and clean place. If they are stored in a wet place, the mold hole corrosion will occur, reducing the service life of the ring mold accessories or materials.
  4. 当装卸环模零件时,不要用锤子等硬钢质工具敲打环模零件表面。
  4. When loading and unloading the ring die parts, do not knock the surface of the ring die parts with a hammer or other hard steel tools.
  5、应做好各班环模配件的使用记录,以统计环模配件的实际使用寿命。
  5. The use records of the ring mold accessories of each shift shall be made to count the actual service life of the ring mold accessories.
  6、若孔塞未出料,可采用油浸或食用油经新造粒后,仍不能使造粒可用电钻将孔塞材料钻出,再用含油性材料加细砂打磨抛光使用。
  6. If the plug is not discharged, oil immersion or edible oil can be used for granulation, but the plug material can not be drilled out by electric drill, and then the oil-bearing material can be used for grinding and polishing with fine sand.
  以上是生物质颗粒机生产厂家分享的环模配件在使用结束时的处理方法,希望对您有所帮助。想要了解更多内容,欢迎访问网站:http://www.longtengkeliji.com
  The above is the treatment method of the ring mold parts shared by the biomass granulator manufacturer at the end of use, hoping to help you. For more information, please visit http://www.longtengkeliji.com

上一篇:木屑颗粒机批发要选大的是为了什么?

下一篇:经过秸秆颗粒机厂家加工过的棉杆有什么用处 ?