生物质颗粒机使用中有哪些应注意的问题

来源:http://www.longtengkeliji.com 发布时间:2019-11-19 浏览次数:
  生物质颗粒机使用中有哪些应注意的问题
  在生物质造粒机的消耗工程中,用户往往不注意一些小细节,更终形成设备检修,不仅影响消耗,而且增加成本。下面小编跟随生物质颗粒机生产厂家大家分享使用中一些注意事项:
  In the consumption engineering of biomass granulator, users often don't pay attention to some small details, and finally form equipment maintenance, which not only affects consumption, but also increases cost. The following editor will share some precautions with the biomass granulator manufacturer:
  1。生物质造粒机停止加工时,为避免压力损失和环模,不得将金属物混入待加工粉末中。
  1. When the biomass granulator stops processing, in order to avoid pressure loss and ring mold, it is not allowed to mix metals into the powder to be processed.
  2。待加工粉末的含水量应在13-20%左右,过高会影响成型,过低会引起梗塞的高温,降低生产能力,也会影响模具寿命。
  2. The moisture content of the powder to be processed should be about 13-20%, too high will affect the molding, too low will cause the high temperature of the infarction, reduce the production capacity, and also affect the mold life.
  3。开机前要检查生物质造粒机加油机是否正常,油路是否畅通,防止轴承等附件被高温烧坏。
  3. Before start-up, check whether the fuel dispenser of biomass granulator is normal and whether the oil circuit is unblocked to prevent the bearing and other accessories from being burnt by high temperature.
  4。生物质造粒机停机时,投料速度不宜过快。大约10分钟后,身体开始发热,然后可以正常速度进食。否则,会因梗塞引起高温。生物质颗粒机生产厂家
  4. When the biomass granulator is shut down, the feeding speed should not be too fast. After about 10 minutes, the body starts to heat up and then can eat at a normal rate. Otherwise, it will cause high temperature due to infarction.
  5个。新的环模必须用磨料磨光。具体方法是:用木屑、金刚砂、发动机油按7:2:1的比例配制磨料,从手动进料口反复倒入,约40分钟。根据生物质造粒机的出料条件和温度变化,及时调整进料速度。对于初期的排料,常见的粉碎现象较多,颗粒形状较小,属于正常现象。几分钟后就可以恢复正常了
  5. The new ring mould must be polished with abrasive. The specific method is: use sawdust, Emery and engine oil to prepare abrasives in the proportion of 7:2:1, pour them repeatedly from the manual feed port for about 40 minutes. Adjust the feeding speed in time according to the discharging conditions and temperature changes of biomass granulator. For the initial discharge, the common crushing phenomenon is more, the particle shape is smaller, which is a normal phenomenon. It'll be back to normal in a few minutes
  6。生物质造粒机在运行过程中,应随时检查各部位螺栓、螺母和管道的紧固情况,防止松动。必须密切注意这一步骤,以防止螺钉松动,对人体或设备本身造成伤害。
  6. During the operation of biomass granulator, the fastening of bolts, nuts and pipes at all parts shall be checked at any time to prevent loosening. Pay close attention to this step to prevent the screw from loosening and causing injury to human body or equipment itself.
  7。生物质造粒机的电流应按正常负荷控制,绝对不允许长时间超过负荷消耗,这是造成设备损坏的主要原因。在整个过程中,生物质造粒机只有在接近满负荷运行时才能达到的消耗状态。
  7. The current of biomass granulator should be controlled according to the normal load, and it is absolutely not allowed to exceed the load consumption for a long time, which is the main cause of equipment damage. In the whole process, the biomass granulator can achieve the best consumption state only when it is close to full load operation.
  8。注意生物质造粒机正常使用时的电流波动,如有异常应停机检查;
  8. Pay attention to the current fluctuation when the biomass granulator is in normal use, and shut down for inspection in case of any abnormality;
  9。新设备投入使用后,连续更换造粒机传动箱500小时,然后根据一般消耗情况每3-6个月更换一次机油,100-120工业齿轮油;
  9. After the new equipment is put into use, the pelletizer transmission box shall be changed continuously for 500 hours, and then the oil and 100-120 industrial gear oil shall be changed every 3-6 months according to the general consumption;
  10。生物质颗粒机堵塞时,必须松开压辊,在清理压模内壁前重新启动压辊。堵转情况下必须停止强制启动,不得用管钳拉齿轮轴。
  10. When the biomass granulator is blocked, the pressing roller must be loosened and restarted before cleaning the inner wall of the pressing die. In case of locked rotor, the forced start must be stopped, and the toothed axle shall not be pulled with pipe tongs.
  11。经常检查造粒机易损件的磨损情况,防止设备突然失效和环模开裂。
  11. Frequently check the wearing condition of vulnerable parts of pelletizer to prevent sudden failure of equipment and cracking of ring mold.
  通过以上分享,我们希望能对您有所帮助。欲了解更多信息,请访问www.longtengkeliji.com
  Through the above sharing, we hope to help you. For more information, visit www.longtengkeliji.com

上一篇:木屑颗粒机批发适用范围及特点!

下一篇:最后一页