生物质燃料颗粒机拆装注意问题?

来源:http://www.longtengkeliji.com 发布时间:2020-12-07 浏览次数:
当我们的生物质燃料颗粒机出现问题后,我们应该怎么处理呢?这是广大客户十分关心的一个问题,因为如果我们不注意,一个小小的零件都有可能把我们的设备毁掉。所以,我们在设备的维护以及维修的时候必须要加以注意,这样才能使我们的颗粒机正常甚至实现超负荷运转不出现问题。下面小编就把燃料颗粒机拆装时需要注意的一些问题介绍给大家:
When our biomass fuel pellet machine has problems, what should we do? This is a problem that the majority of customers are very concerned about, because if we do not pay attention, a small part may destroy our equipment. Therefore, we must pay attention to the maintenance and repair of the equipment, so as to make our granulator normal and even realize overload operation without problems. The following is a small series of fuel pellet machine assembly and disassembly need to pay attention to some problems to introduce to you:
1、一般情况下不需要拆进料罩,只需要打开制粒室上的观察窗口来检查压轮的工作情况。
1. In general, it is not necessary to remove the feeding cover, but to open the observation window on the granulating chamber to check the working condition of the pressure roller.
2、如果需要更换压轮或者更换模具时,则需要拆下进料罩和压轮仓拧下上面的螺钉和螺母,再将主轴上的锁紧螺母拧下,把压轮总成用吊装带将其整个吊起挪出压轮仓外,然后再用两个吊装螺钉拧到模盘上的工艺孔,用吊装带将其吊起,再把模具另一面反过来使用。
2. If it is necessary to replace the pressure wheel or mold, it is necessary to remove the feeding cover and the pressure wheel bin, screw off the screws and nuts on the upper part, and then screw the locking nut on the main shaft, lift the whole pressure wheel assembly out of the pressure wheel warehouse with hoisting belt, and then screw the pressure wheel assembly to the process hole on the die plate with two lifting screws, lift it with lifting belt, and then use the other side of the mold in reverse 。
3、如果压轮皮或是压轮轴承需要更换,需要把压轮上的外密封盖拆下,把压轮轴上的圆螺母拆下,再把压轮轴承从里向外赶出来,轴承拆下后需要更换或是不更换(用柴油清洗),压轮内孔要保持清洁,然后按反顺序把压轮总成安装即可。
3. If the pressure wheel skin or pressure wheel bearing needs to be replaced, the outer sealing cover on the pressure wheel should be removed, the round nut on the pressure shaft should be removed, and then the pressure wheel bearing should be driven out from the inside out. After the bearing is removed, the bearing needs to be replaced or not replaced (cleaned with diesel oil). The inner hole of the pressure wheel should be kept clean, and then the pressure wheel assembly can be installed in reverse order.
             生物质颗粒机生产厂家
生物质燃料颗粒机因其独特的特点现在被越来越广泛的应用,在使用颗粒机的时候要防范一些常见问题出现,这样才能使颗粒机更工作的同时还能延长使用寿命。
Due to its unique characteristics, biomass fuel pellet machine is now more and more widely used. When using the pellet machine, we should prevent some common problems, so as to make the granulator work more efficiently and prolong its service life.
生物质燃料颗粒机使用时注意问题如下:
The matters needing attention in the use of biomass fuel granulator are as follows:
1、颗粒机初运转阶段不要添加过多原料,在磨合期内,新机器产量一般要比额定产量要低一些,但度过磨合期以后,产量便会达到机械本身的额定产量。
1. During the running in period, the output of the new machine is generally lower than the rated output, but after the running in period, the output will reach the rated output of the machine itself.
2、颗粒机研磨时特别注意方面分析,颗粒机刚买到后运行前需要进行磨合,在正式使用前,合理的研磨对颗粒机对机器后期使用有非常重要的影响,燃料颗粒机的环模压辊是热处理件,在热处理过程当中,在环模的内孔有一些毛刺,这些毛刺在颗粒机的运行过程中会阻碍物料的流动与成型。严禁向喂料装置内加入硬杂物,以免损坏模具,影响颗粒机生产效率及颗粒机寿命。
2. Special attention should be paid to the analysis of aspects when grinding the granulator. It is necessary to run in the granulator just after it is purchased and before it is put into operation. Before formal use, reasonable grinding has a very important impact on the later use of the granulator. The annular mold pressing roller of the fuel granulator is a heat treatment part. During the heat treatment process, there are some burrs in the inner hole of the ring mold, which are in the operation process of the granulator It will hinder the flow and forming of materials. It is strictly forbidden to add hard impurities into the feeding device to avoid damaging the mold and affecting the production efficiency and service life of the granulator.
3、生物质颗粒机的光滑与冷却工序方面,颗粒机的压辊要将木屑等质料挤压到模具内孔里,并将反面的原料推到前面的原料里,颗粒机的压辊直接影响着颗粒的成型。
3. In terms of the smoothness and cooling process of biomass granulator, the pressure roller of the granulator should extrude the sawdust and other materials into the inner hole of the mould, and push the raw materials on the back side into the raw materials in front of the pelletizer. The pressing roller of the granulator directly affects the shaping of the granules.
,为了保障生产安全进行,严禁疲劳操作机器。
Finally, in order to ensure the safety of production, fatigue operation of the machine is strictly prohibited.

上一篇:秸秆颗粒机处理后的秸秆块的燃烧方式!

下一篇:木屑颗粒机憋机的原因是什么?