秸秆颗粒机具备的高行程有哪些?

来源:http://www.longtengkeliji.com 发布时间:2020-07-20 浏览次数:
控制粗纤维材料的含量。 粗纤维是秸秆造粒过程中非常重要的因素。 含量太多,粘结性差,难以压制成型,含量太小,不利于成型。 通常,对照约为5%。 我们会联系具体的价值。 我们根据您的具体情况给出计算结果。
Control the content of crude fiber material. Crude fiber is a very important factor in the process of straw granulation. Too much content, poor adhesion, difficult to press molding, content is too small, not conducive to molding. Generally, the control is about 5%. We will link specific values. We give the calculation results according to your specific situation.
添加油脂。 当秸秆颗粒机用作燃料颗粒机时,需要向材料中加入适量的油,约0.8%。 添加润滑脂有两个优点,一是减少机器的磨损,提高机器的使用寿命。 其次,材料变得易于压制和形成并增加产量。 应该指出的是,控制量不应过多。 添加方法通常是在混合搅拌部分中添加30%,并在造粒机中喷洒70%。 如果你使用秸秆颗粒机制作饲料颗粒,不要,或者你不能吃颗粒状的动物。
Add grease. When straw granulator is used as fuel granulator, it is necessary to add an appropriate amount of oil, about 0.8%. Adding grease has two advantages. One is to reduce the wear of the machine and improve the service life of the machine. Second, the material becomes easier to press and form and increase yield. It should be noted that the amount of control should not be excessive. The addition method is usually 30% in the mixing and mixing section and 70% spraying in the granulator. If you use a straw pelletizer to make feed pellets, don't, or you can't eat granular animals.
秸秆颗粒机厂家
水分控制在13%左右。 对于生物质燃料,应严格控制材料的水分。 这是将材料压成颗粒的前提。 如果水分太高,颗粒会松动。 这不是很多,但请记住。
The moisture content was controlled at about 13%. For biomass fuel, the moisture content should be strictly controlled. This is the premise of pressing the material into particles. If the moisture is too high, the particles will become loose. It's not a lot, but remember.
如果生物质秸秆颗粒机使用不当,产量将低于标准预期产量。 如果使用时间很长,则产量会下降。 作为生物质木质颗粒的制造商,我们有以下建议。
If the biomass straw granulator is not used properly, the output will be lower than the standard expected output. If used for a long time, the yield will decrease. As a manufacturer of biomass wood particles, we have the following suggestions.
1.调整原料的水分含量。 抑制生物质颗粒所需的锯末和锯末等原料的水分含量约为13%。 太高或太低都会降低产量。
1. Adjust the moisture content of raw materials. The moisture content of sawdust and sawdust is about 13%. Too high or too low will reduce the yield.
2.调整颗粒机的参数。 例如,压力辊和模具之间的间隙。 不同材料需要不同的间隙。 输出低,可能是间隙未正确调整。 让制造商调整它。
2. Adjust the parameters of the granulator. For example, the gap between the pressure roller and the mold. Different materials require different clearances. The output is low, the gap may not be adjusted correctly. Let the manufacturer adjust it.
3.新模具应磨削。 限于秸秆颗粒机的机械制造水平,新模具的模腔平滑度达不到秸秆颗粒机的水平。 研磨方法也很简单,好多次按压油,沙和木屑的混合物。 详细过程可以询问制造商,或联系我们的客户服务。
3. The new mould should be ground. Limited to the mechanical manufacturing level of the straw granulator, the smoothness of the cavity of the new mold can not reach the level of the straw granulator. The grinding method is also very simple. Press the mixture of oil, sand and sawdust many times. Detailed process can be asked the manufacturer, or contact our customer service.
4.做好机器维护,及时更换模具。 模具和压辊秸秆颗粒机需要很长时间才能引起磨损,这是不可避免的。 如果这是生产下降的原因,好更换新模具。
4. Do a good job in machine maintenance and timely replace the mold. It takes a long time for the mould and press roller straw granulator to cause wear, which is inevitable. If this is the reason for the decline in production, replace the mold with a new one.
感谢您的阅读,此文的文章来源:秸秆颗粒机厂家更多的内容和问题请点击:http://www.longtengkeliji.com我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading. This article is from: straw granulator manufacturer. For more information and questions, please click: http://www.longtengkeliji.com We will continue to work hard to provide services for you, thank you for your support!

上一篇:生物质颗粒机压轴打滑问题怎么处理?、

下一篇:最后一页